The LCD20x4 is a character LCD (Liquid Crystal Display) module that typically has 20 columns and 4 rows of characters. It is commonly used in embedded systems and other electronic devices to display text and simple graphics.
If your LCD20x4 module does not have I2C specifications, it is likely th ...at it uses a parallel interface to communicate with a microcontroller or other device. In this case, you will need to connect multiple data pins and control pins between the LCD and the microcontroller.
Here are the basic connections required to interface an LCD20x4 module with a microcontroller:
- VCC: Connect this pin to a +5V power supply.
- GND: Connect this pin to ground.
- RS (Register Select): This pin is used to select whether data or instructions are being sent to the LCD. Connect it to a microcontroller output pin.
- R/W (Read/Write): This pin is used to select whether data is being read from or written to the LCD. Connect it to ground to enable writing only.
- E (Enable): This pin is used to signal the LCD that data is ready to be read or written. Connect it to a microcontroller output pin.
- D0-D7 (Data): These pins are used to send data to the LCD. Connect them to microcontroller output pins.
In addition to these basic connections, you may also need to connect a contrast adjustment potentiometer and backlight control pins, depending on the specific requirements of your LCD module.
Once you have connected the LCD20x4 module to your microcontroller, you will need to write software to initialize the LCD and send data and commands to it. This typically involves sending commands to set the cursor position, clear the display, and write characters to the LCD. The specific commands and timing requirements will depend on the controller used in your LCD module.
Resistor 1Ω-120MΩ OHM - 1/4W 5%
Ksh 2.00
Delivered Friday, February 14
100PCS Rectifier Diode 1N4007 IN4007 DO-41 1A
Ksh 5.00
Delivered Friday, February 14
Ceramic capacitor 1pF - 2.2uF
Ksh 5.00
Delivered Friday, February 14
Diffused Red 3mm LED
Ksh 5.00
Delivered Friday, February 14
MALE TO MALE HEADER PIN 1×40 2.54 MM STRAIGHT
Ksh 20.00
Delivered Friday, February 14
Female HEADER PINS 1×40 1.27MM PITCH for PCBs and prototype boards
Ksh 20.00
Delivered Friday, February 14
12x12x7mm Tactile 4 Pin Push Button Switch
Ksh 5.00
Delivered Friday, February 14
Diffused Green 5mm LED
Ksh 5.00
Delivered Friday, February 14
Diffused Blue 5mm LED
Ksh 5.00
Delivered Friday, February 14
7mmx190mm Transparent Glue Sticks
Ksh 40.00
Delivered Friday, February 14
Buzzer Piezoelectric Active
Ksh 30.00
Delivered Friday, February 14
Diffused White 3mm LED
Ksh 5.00
Delivered Friday, February 14
FEMALE -MALE JUMPER WIRE 40PCS DUPONT
Ksh 150.00
Delivered Friday, February 14
Arduino Uno R3 Removable Atmega board
Ksh 1,600.00
Delivered Friday, February 14
MALE TO MALE JUMPER WIRE 40 PCS DUPOINT M-M
Ksh 150.00
Delivered Friday, February 14
Arduino Pro Mini 5V 16mhz
Ksh 500.00
Delivered Friday, February 14
Diffused Yellow 3mm LED
Ksh 5.00
Delivered Friday, February 14
HC-SR501 PIR Motion sensor
Ksh 200.00
Delivered Friday, February 14
ARDUINO UNO R3 MEGA-328PCH340G with Fixed/SMD CHIP
Ksh 1,200.00
Delivered Friday, February 14
SIM 800LGPRS GSM BREAKOUT MODULE WITH antenna
Ksh 1,000.00
Delivered Friday, February 14